HomeRefurbers

Tools, Hardware & Accessories

Not sure what the right tool is for the job? This forum is the place to discuss tools and other resources available to get the job done right.

Topics Replies Last post
View bryonbuzz's profile

side mounted cargo racks made by a contractor for contractors

04-16-2014 02:43 PM by bryonbuzz

here is a tool that will save you money every time you use it a side mounted ...

74 12-14-2017 05:09 PM
View swoop42's profile

J-Line Bandsaw

04-04-2010 03:25 AM by swoop42

I just got an old J-Line Bandsaw that has been in storage for several years. ...

144 12-14-2017 11:06 AM
View chicagotom's profile

Right tool for butcherblock cut

11-13-2015 10:02 PM by chicagotom

Putting some 1 1/2” butcher block in the laundry room. Putting in a sin...

160 12-14-2017 10:50 AM
View handystanley's profile

Framing Nailer - Corded or Cordless That IS the Question

11-09-2012 06:41 PM by handystanley

Although I have seen a couple of posts similar, I am going to ask this anyway...

297 12-14-2017 09:57 AM
View crank49's profile

Why can't Shark Bite fittings be sold in California or Vermont?

06-21-2011 01:42 AM by crank49

I just installed a new faucet in my kitchen and decided to use Shark Bite fit...

645 12-14-2017 08:34 AM
View Trog's profile

Which jobsite table saw ?

06-14-2017 02:58 AM by Trog

Hello,new member in search of advice. By the end of this year we should ha...

139 12-13-2017 11:10 AM
View Dalec's profile

How to make kerf cuts in polystrene or styrofoam boards?

02-01-2009 02:10 AM by Dalec

Have been looking at ways to insulate my garage door. I found several web si...

26 12-13-2017 07:31 AM
View milz45's profile

Looking for a HVLP sprayer for approx $150 and thinning advice!

12-03-2009 09:53 PM by milz45

I posted this over at Lumberjocks, but thought I’d stick it here too. ...

78 12-12-2017 06:10 AM
View davidroberts's profile

I'm Shocked, 16 Gauge Pneumatic Staplers

10-06-2010 05:43 AM by davidroberts

A comment or two and a question or three. I have just picked myself up off...

49 12-12-2017 06:08 AM
View popselectric's profile

Electricians tool belt HELP!!

12-02-2013 07:16 PM by popselectric

I’ve been working as an electrician for about a year now. I have a R...

41 12-05-2017 08:10 PM
View Gary's profile

Tool for flush cutting nails under tack strips?

05-28-2012 02:16 PM by Gary

I’m taking out carpet in order to use the terrazzo underneath.I was tol...

108 12-03-2017 02:29 AM
View Olaf Gradin's profile

OSB vs. SturdiFloor (OSB)

10-10-2008 03:51 PM by Olaf Gradin

My existing flooring appears to be 5/8” OSB, non-T&G. I am putting...

45 11-29-2017 02:14 PM
View tenontim's profile

Stud Sensor

04-28-2008 11:48 PM by tenontim

I bought one of these Zircon stud sensors from Lee Valley a few months ag...

21 11-27-2017 06:11 AM
View NY_Rocking_Chairs's profile

Anyone familiar with the mortar-less brick siding?

01-20-2009 04:00 PM by NY_Rocking_Chairs

Hello, We are in the planning stages of putting a new patio on and eventua...

64 11-27-2017 06:01 AM
View John's profile

Bent bristles on paint brush

01-16-2014 11:47 AM by John

Bristles on one of my good paint brushes have taken a slight curve. Evidentl...

40 11-27-2017 05:59 AM
View Janan's profile

RAlph Lauren Glaze????HELP!

11-16-2009 05:56 AM by Janan

Does any one know where I can find Ralph Lauren Tea stain Glaze? I used to ge...

80 11-25-2017 01:43 AM
View Eddy's profile

Sick of painting by hand. Anyone use sprays?

03-15-2009 05:48 AM by Eddy

I have painted and clear coated all the trim and doors before being installed...

81 11-25-2017 01:11 AM
View Dan Lyke's profile

Tile Saw: Rent or Buy?

11-03-2014 08:54 PM by Dan Lyke

So we’re going to be re-tiling the bathroom walls, with 18” tiles...

96 11-25-2017 01:06 AM
View bryonbuzz's profile

useing side mounted cargo racks to carry sheet goods and lumber

02-19-2014 10:40 PM by bryonbuzz

I have been using a side mounted cargo rack for the past 2 years to pick up m...

53 11-21-2017 07:44 AM
View sikrap's profile

Cordless Nailers

03-21-2009 01:59 AM by sikrap

Hi, I’ve got a few roofing jobs coming up now that I’ve retired f...

17 11-15-2017 12:25 PM

1 2 3
51 topics


DISCLAIMER: All views and comments posted by members are not necessarily those of HomeRefurbers.com or of those working on the site.

Latest Projects | Latest Blog Entries | Latest Forum Topics

LumberJocks.com :: woodworking showcase